- Curtis 1314 Pc Programming Software
- Curtis Programmer Free Download
- Curtis Controller Programming Software Downloads
- Curtis Controller Programming Software Download Windows 7
- Curtis Speed Controller
1 Curtis 1268 electronic motor controller. These controllers are fully programmable by means of the optional 1311 handheld programmer or 1314 PC programming station. Use of a programmer provides diagnostic and test capability as well as configuration flexibility and the ability to easily transfer settings from one controller to another. The 1314 Windows PC Software Tool is intended for use by vehicle OEMs, dealers, and service engineers. It provides a powerful Windows interface for adjusting settings, troubleshooting, and recording the parameters of any Curtis speed controller or auxiliary device. FEATURES. View and adjust controller programmable parameters.
As the new member of 1204M / 1205M series winding motor speed controllers, the controller model 1204M-4201 has an extra 'J5' terminal which offers new function 'reverse signal input' or 'main contactor driver' (corresponding controller parameter 'Rev Input / Main Driver').The parameter 'Rev Input / Main Driver' determines the signal input at the controller’s J5 terminal:
- 0 = reverse input and main driver both inactive; use this setting if you are replacing an earlier model with no J5 terminal and want to leave the wiring as it was.
- 1 = reverse input active (see page 7, figure 5 of controller manual).
- 2 = main driver active (see page 7, figure 4 of controller manual).
It is quite simple to connect a CURTIS programmer to controller 1204M-4201. If you are going to diagnose or reprogram a 1204M-4201 in your office, you may prepare a 24V DC power source for feeding the power to the controller and to the programmer.
Curtis 1314 Pc Programming Software
- Put the MOLEX 4-Pin connector of programmer communicating cable into the mating connector of controller 1204M-4201.
- Connect the power source positive (B+) to the controller B+ main terminal and J1 terminal.
- Connect the power source negative (B-) to the controller B- main terminal.
- switch on the DC power source, then you will see the initiating screen (handheld programmer) or you can start to connect the controller (PC Station programmer).
- Entering the programmer manual, you may choose to:
- modify the controller parameters
- monitoring the controller status
- diagnosing the controller
- viewing the error history
Relatively, programming a 1204M-4201 is relative simpler than the programming process of other CURTIS controller models. For each different controller models, CURTIS configures a different terminal setting for programmers. But there are some points are common:
- A KSI (key switch input) terminal is always available for activating the controller.
- For activating the logical circuit of a CURTIS controller, a 24V DC power (max. the rated working voltage of controller) positive (B+) should be connected to the KSI terminal.
- For some controller models, a dedicated logical enable terminal is available, should also be feed by the same B+, like KSI.
- The DC power negative (B-) should be connected to B- terminal of controller, for constructing a complete working circuit.
Curtis Programmer Free Download
As the new member of 1204M / 1205M series winding motor speed controllers, the controller model 1204M-4201 has an extra 'J5' terminal which offers new function 'reverse signal input' or 'main contactor driver' (corresponding controller parameter 'Rev Input / Main Driver').The parameter 'Rev Input / Main Driver' determines the signal input at the controller’s J5 terminal:
- 0 = reverse input and main driver both inactive; use this setting if you are replacing an earlier model with no J5 terminal and want to leave the wiring as it was.
- 1 = reverse input active (see page 7, figure 5 of controller manual).
- 2 = main driver active (see page 7, figure 4 of controller manual).
It is quite simple to connect a CURTIS programmer to controller 1204M-4201. If you are going to diagnose or reprogram a 1204M-4201 in your office, you may prepare a 24V DC power source for feeding the power to the controller and to the programmer.
Curtis Controller Programming Software Downloads
- Put the MOLEX 4-Pin connector of programmer communicating cable into the mating connector of controller 1204M-4201.
- Connect the power source positive (B+) to the controller B+ main terminal and J1 terminal.
- Connect the power source negative (B-) to the controller B- main terminal.
- switch on the DC power source, then you will see the initiating screen (handheld programmer) or you can start to connect the controller (PC Station programmer).
- Entering the programmer manual, you may choose to:
- modify the controller parameters
- monitoring the controller status
- diagnosing the controller
- viewing the error history
Curtis Controller Programming Software Download Windows 7
Relatively, programming a 1204M-4201 is relative simpler than the programming process of other CURTIS controller models. For each different controller models, CURTIS configures a different terminal setting for programmers. But there are some points are common:- A KSI (key switch input) terminal is always available for activating the controller.
- For activating the logical circuit of a CURTIS controller, a 24V DC power (max. the rated working voltage of controller) positive (B+) should be connected to the KSI terminal.
- For some controller models, a dedicated logical enable terminal is available, should also be feed by the same B+, like KSI.
- The DC power negative (B-) should be connected to B- terminal of controller, for constructing a complete working circuit.